HARDOX® 550
STEP UP YOUR WEAR RESISTANCE
Higher hardness for longer wear life in severe wear

Extra Hardness for Extreme Wear
Hardox® 550 is an extra-hard wear-resistant steel designed for applications where severe abrasion demands significantly higher wear resistance and longer service life. With a nominal hardness of 550 HBW, it provides a substantial step up in wear performance compared with Hardox® 500.
Hardox® 550 combines very high hardness with good toughness, making it particularly suitable for components exposed to intense sliding and abrasive wear where maximizing service life is the primary objective.
Extra Hardness for Longer Wear Life
The key advantage of Hardox® 550 is its 550 HBW nominal hardness. The additional hardness significantly increases resistance to abrasive wear and can extend component life compared with lower-hardness wear steels.
For applications currently using Hardox® 500 or conventional 500 HBW wear plate, upgrading to Hardox® 550 can provide a considerable increase in wear life. The actual improvement depends on the abrasive material, operating conditions, component design and wear mechanism.
Why Upgrade to Hardox® 550?
Superior Abrasion Resistance
With a nominal hardness of 550 HBW, Hardox® 550 provides excellent resistance to severe abrasive wear, making it particularly effective in applications involving hard and aggressive materials.
Longer Service Life
Higher wear resistance means components can remain in operation for longer periods, reducing replacement frequency and increasing equipment availability.
Lower Maintenance and Downtime
Longer-lasting wear parts require fewer replacements. This helps reduce maintenance requirements, planned shutdowns and associated operating costs.
Potential for Thinner Wear Parts
In suitable applications, the higher wear resistance of Hardox® 550 can allow thinner wear components to be used while maintaining the required service life. This can reduce material consumption and component weight.
Good Workshop Performance
Despite its very high hardness, Hardox® 550 offers good workshop properties for a steel in this hardness range. With appropriate procedures and equipment, it can be cut, welded, machined and formed into demanding wear components.
Designed for Severe Abrasive Wear
Hardox® 550 is especially suitable when abrasion is the dominant wear mechanism and Hardox® 500 does not provide sufficient service life.
Its high hardness provides strong resistance to material loss caused by sliding, scraping and continuous contact with abrasive materials such as rock, minerals, sand, gravel, concrete and recycled materials.
This makes Hardox® 550 an effective solution for equipment operating continuously in highly abrasive environments.
Typical Applications
Hardox® 550 is particularly suitable for:
•Wear liners
•Chutes and hoppers
•Crushers and recycling equipment
•Screens and sieves
•Mining and quarrying equipment
•Concrete and aggregate handling equipment
•Wear strips and wear plates
•Heavy-duty industrial wear components
•Components exposed to severe sliding abrasion
More Hardness. More Wear Life.
Hardox® 550 takes wear performance beyond Hardox® 500 by combining 550 HBW hardness with good toughness and workshop properties.
For manufacturers and equipment operators, this higher level of wear resistance can provide longer replacement intervals, reduced downtime, lower maintenance requirements and improved operating efficiency.
Choose Hardox® 550 when extreme abrasive wear requires more hardness, longer service life and maximum wear performance.
Applications
Tech information
Mechanical Properties
Thickness | Hardness 1) (HBW) |
|---|---|
8.0 - 65.0 | 525 - 575 |
1) Brinell hardness, HBW, according to EN ISO 6506-1, on a milled surface 0.5 – 3 mm below surface. At least one test specimen per heat and 40 tons.
The nominal thickness of supplied plates will not deviate more than +/- 15 mm from the thickness of the test specimen used for hardness testing.
Hardox is through-hardened. Minimum core hardness is 90 % of the guaranteed minimum surface hardness.
Impact Properties
Grade | Longitudinal test, typical impact energy, Charpy V 10x10 mm test specimen. |
|---|---|
Hardox 550 | 30J / -40°C |
Tolerances
Tolerances
More details are given in SSAB´s brochure 41-General product information Strenx, Hardox, Armox and Toolox-UK and Hardox Guarantees or on www.ssab.com.
Thickness
Tolerances according to Hardox Thickness Guarantees. Hardox® Guarantees meets the requirements of EN 10 029 Class A but offers more narrow tolerances.
Length and Width
According to SSAB´s dimensions program. Tolerances according to SSAB´s mill edge standards or tolerances that conform to EN 10 029.
Shape
Tolerance according to EN 10 029.
Flatness
Tolerances according to Hardox Flatness Guarantee class E, which are more restrictive than EN 10 029 Class N.
Surface Properties
EN 10163-2 Class A Subclass 1.
Chemical Composition

Chemical Composition (heat analysis)
C*) | Si*) | Mn*) | P*) | S *) | Cr*) | Ni*) | Mo*) | B*) |
|---|---|---|---|---|---|---|---|---|
0.44 | 0.50 | 1.30 | 0.020 | 0.010 | 1.40 | 1.40 | 0.60 | 0.004 |
The steel is grain refined. *) Intentional alloying elements.
Carbon Equivalent CET(CEV)
Thickness | 8 - 31.9 | 32 - 51 | 51.1 - 65 |
|---|---|---|---|
Max CET(CEV) | 0.49(0.70 | 0.52(0.75) | 0.61(0.82) |
Typ CET(CEV) | 0.46(0.67) | 0.49(0.72) | 0.58(0.79) |
Delivery Conditions
The delivery condition is Q or QT (Quenched or Quenched and Tempered). The plates are delivered with sheared or thermally cut edges. Untrimmed mill edges available by agreement.
Delivery requirements can be found in SSAB´s brochure 41-General product information Strenx, Hardox®, Armox and Toolox-UK or at www.ssab.com.





