Damatech
High Performance SteelValue Added ProcessingInnovative Industrial SolutionsDamatech

HARDOX® 500Tuf

UPGRADE YOUR WEAR PERFORMANCE

Step up from HARDOX® 450 to 500 Tuf for longer wear life.

img-Hardox-500-Tuf1-600-600-p-L-97

New Generation of Wear-Resistant Steel

Hardox® 500 Tuf represents a new generation of wear-resistant steel, combining the high wear resistance of 500 HBW steel with exceptional toughness and structural performance. This unique combination sets it apart on the market and opens new possibilities for applications where conventional wear steels require a compromise between hardness, toughness and workshop performance.

With a nominal hardness of 500 HBW, Hardox® 500 Tuf provides significantly higher wear resistance than Hardox® 450 while maintaining the toughness required for applications exposed to heavy impact and dynamic loads.

The result is a wear steel designed not only to last longer, but also to enable lighter, stronger and more efficient equipment.

A Unique Combination of Hardness and Toughness

What makes Hardox® 500 Tuf different is its ability to combine 500 HBW hardness with exceptionally high toughness.

Traditionally, increasing hardness meant accepting lower toughness and a higher risk of cracking under severe impact. Hardox® 500 Tuf changes this balance by combining high wear resistance with the toughness and structural properties required for demanding applications.

This makes it a unique solution in the wear steel market, particularly for applications where abrasion, impact and structural loads occur simultaneously.

Why Upgrade to Hardox® 500 Tuf?

Longer Wear Life

The 500 HBW hardness provides significantly higher resistance to abrasive wear compared with Hardox® 450. Longer component life means fewer replacements, less downtime and more productive operating hours.

Exceptional Toughness at 500 HBW

The defining advantage of Hardox® 500 Tuf is its combination of very high hardness and excellent impact toughness. Components can withstand severe abrasive wear while remaining resistant to impact, shock and dynamic loads.

Lower Total Cost of Ownership

Longer service life can reduce replacement frequency, maintenance requirements and downtime. This contributes to a lower cost per operating hour or cost per transported tonne.

Potential for Weight Reduction and Higher Payload

The combination of high strength, toughness and wear resistance can enable thinner plate to be used in suitable designs. This creates opportunities to reduce equipment weight and increase payload without compromising wear performance or structural reliability.

Excellent Workshop Properties

Despite its 500 HBW hardness, Hardox® 500 Tuf offers excellent workshop performance. It can be welded, bent, cut and machined using established processing methods, making it possible to manufacture advanced wear-resistant structures efficiently.

Wear Resistance Without Compromising Toughness

Hardox® 500 Tuf brings together properties that traditionally required a compromise.

Its 500 HBW hardness provides excellent resistance to abrasive wear, while its high toughness helps components withstand impact and demanding operating conditions.

This combination makes Hardox® 500 Tuf particularly suitable for applications where abrasion and impact occur simultaneously, providing a new level of performance compared with conventional wear-resistant steels.

Typical Applications

Typical Applications

Hardox® 500 Tuf is particularly suitable for:

•Dump and tipper bodies

•Mining and quarrying equipment

•Excavator and loader buckets

•Crushers and recycling equipment

•Containers

•Chutes and hoppers

•Wear liners

•Demolition equipment

•Heavy-duty transport equipment

A New Standard in Wear Performance

Hardox® 500 Tuf is more than simply a harder wear plate. It represents a new generation of wear-resistant steel, combining 500 HBW hardness, exceptional toughness, structural capability and excellent workshop properties in one material.

For manufacturers and equipment operators, this unique combination creates opportunities for longer service life, lower equipment weight, higher payload, reduced downtime and increased productivity.

Choose Hardox® 500 Tuf when you need a unique combination of extreme wear resistance, toughness and structural performance – without compromise.

Tech information

Mechanical Properties


Thickness
(mm)

Hardness 1) (HBW)

Typical yield strength (MPa), not guaranteed

4.0 - 25.4

475 - 505

1250 - 1400

1) Brinell hardness, HBW, according to EN ISO 6506-1, on a milled surface 0.5 – 3 mm below surface. At least one test specimen per heat and 40 tons.

The nominal thickness of supplied plates will not deviate more than +/- 15 mm from the thickness of the test specimen used for hardness testing.

Hardox is through-hardened. Minimum core hardness is 90 % of the guaranteed minimum surface hardness.

Impact Properties


Grade

Longitudinal test, typical impact energy, Charpy V 10x10 mm test specimen.

Hardox 500 Tuf 1)

27J / -20°C

1)  Impact toughness measured upon agreement. For thicknesses between 6 - 11.9 mm, subsize Charpy V-specimens are used. The specified toughness is then proportional to the cross-sectional area of the test specimen, compared to a full-size specimen (10 x 10 mm). Impact testing according to ISO EN 148. Average of three tests.

Tolerances

Tolerances
More details are given in SSAB’s brochure 41-General Product Information Strenx, Hardox, Armox and Toolox-UK and Hardox Guarantees or at www.ssab.com.

Thickness
Tolerances according to Hardox Thickness Guarantees. Hardox® Guarantees meets the requirements of EN 10 029 Class A.

Length and Width
According to SSAB’s dimension program. Tolerances according to SSAB´s mill edge standards or tolerances that conform to EN 10 029.


Shape
Tolerances according to EN 10 029.

Flatness
Tolerances according to Hardox Flatness Guarantees Class D, which are more restrictive than EN 10 029.

Surface Properties
According to EN 10 163-2, Class A Subclass 1.

Bending
Bendability according to Hardox Bending Guarantees Class E.

Chemical Composition
Carbon Equivalent CET(CEV)

Chemical Composition (heat analysis)

C*)
(max %)

Si*)
(max %)

Mn*)
(max %)

P*)
(max %)

S *)
(max %)

Cr*)
(max %)

Ni*)
(max %)

Mo*)
(max %)

B*)
(max %)

0.30

0.70

1.60

0.020

0.010

1.50

1.50

0.60

0.005

The steel is grain refined. *) Intentional alloying elements.

Carbon Equivalent CET(CEV)

Thickness

sheet
4.0 - 16.0

plate
16.1 - 25.4

Max CET(CEV)

0.38(0.54)

0.39(0.55)

Typ CET(CEV)

0.36(0.52)

0.37(0.53)

Delivery Conditions

The delivery condition is Q or QT (Quenched or Quenched and Tempered). The plates are delivered with sheared or thermally cut edges.

Tech Support

Hardox® Documents to Download

Hardox Downloads

Video

Hardox Steel Grades & Shapes