Damatech
High Performance SteelValue Added ProcessingInnovative Industrial SolutionsDamatech

HARDOX® 450

TAKE WEAR PERFORMANCE FURTHER

More wear resistance. More performance. Longer life.

Hardox 450 Liner Plate

Hardox® 450 – Upgrade Your Wear Performance

The Smart Upgrade from Standard 400 HB Wear Plates

When standard 400 HB wear-resistant plates no longer deliver the required service life, Hardox® 450 offers a proven step forward in wear performance.

With a nominal hardness of 450 HBW, Hardox® 450 combines higher resistance to abrasive wear and denting with excellent toughness and workshop properties. This makes it an ideal choice for customers looking to extend component life, reduce maintenance costs and improve equipment productivity.

Compared with conventional 400 HB wear-resistant plates, Hardox® 450 offers an additional 50 HBW in nominal hardness, providing greater resistance to wear without compromising manufacturing efficiency.

From 400 to 450 HBW – A Smart Performance Upgrade

Upgrading from standard 400 HB wear plates to Hardox® 450 increases nominal hardness by approximately 12.5%, but the potential improvement in wear life can be significantly greater.

Depending on the abrasive material, operating conditions and wear mechanisms, the higher hardness of Hardox® 450 can deliver a substantial increase in component service life.

More hardness. Longer wear life. Lower operating costs.

For equipment manufacturers and end users, this means more operating hours from the same component, fewer replacements and improved productivity.

Hardox® 450 – More Performance from Every Component

Choosing Hardox® 450 instead of conventional 400 HB wear-resistant plates is not simply a matter of increasing hardness. It is an opportunity to improve equipment performance, extend maintenance intervals and reduce lifetime operating costs.

Upgrade from standard 400 HB wear plates to Hardox® 450 – and turn higher wear resistance into measurable customer value.

Why Upgrade from Standard 400 HB Wear Plates to Hardox® 450?
HX450 tabela1

Longer Wear Life

Higher hardness provides increased resistance to abrasive wear. Compared with conventional 400 HB wear plates, Hardox® 450 can significantly extend component service life, reducing replacement frequency and increasing equipment availability.

Higher Resistance to Denting

Hardox® 450 offers improved resistance to permanent surface deformation and denting. Its combination of hardness and toughness makes it particularly suitable for demanding applications involving abrasive materials, impact and heavy loads.

Lower Total Cost of Ownership

Longer service life means fewer replacement parts, reduced maintenance requirements and less unplanned downtime.

Although material cost is only one part of the overall operating expense, upgrading to Hardox® 450 can significantly reduce the cost per operating hour or tonne of material processed.

Potential for Weight Reduction

The higher strength and wear resistance of Hardox® 450 may allow thinner plates to be used in applications where design requirements permit.

This creates opportunities to reduce equipment weight, increase payload capacity and improve operational efficiency while maintaining the required wear performance and structural integrity.

Excellent Workshop Properties

Hardox® 450 combines improved wear performance with excellent processing characteristics.

It can be cut, welded, bent and machined using established workshop methods and appropriate processing recommendations.

For manufacturers already working with standard 400 HB wear-resistant plates, the transition to Hardox® 450 can be straightforward, without major changes to existing production processes.

Typical Applications

Hardox® 450 is widely used for:

•Dump and tipper bodies

•Excavator and loader buckets

•Wear liners

•Chutes and hoppers

•Containers

•Crushers and recycling equipment

•Mining and quarrying equipment

•Agricultural and earthmoving equipment

•Material-handling equipment

Tech information

Mechanical Properties


Grade

Thickness
(mm)

Hardness 1)
(HBW)

Tesnile strength
Rm
(MPa),
guaranteed

Typical yield
strength
(MPa), not
guaranteed

Hardox 450 CR sheet

0.7 - 2.10

425 - 4752)

1370 - 1600

1250

Hardox 450 sheet

2.0 - 8.0

425 - 475

-

1250

Hardox 450 plate

3.2 - 80.0

425 - 475

-

1250

Hardox 450 plate

80.1 - 103.0

410 . 475

-

1250

Hardox 450 plate

103.1 - 130.0

390 . 475

-

1250

1) Brinell hardness, HBW, according to EN ISO 6506-1, on a milled surface 0.5 – 3 mm below surface. At least one test specimen per heat and 40 tons.
2) Hardness test is not performed or guaranteed for Hardox 450 cold rolled material. The hardness interval is a conversion from the tensile strength. The nominal thickness of supplied plates will not deviate more than +/- 15 mm from the thickness of the test specimen used for hardness testing.

Hardox is through-hardened. Minimum core hardness is 90% of the guaranteed minimum surface hardness.

Impact Properties

Grade

Longitudinal test, typical impact energy, Charpy V 10x10 mm test specimen. 1)

Transverse test, guaranteed impact energy, Charpy V 10x10 mm test specimen.

Hardox 450 sheet & plate

50 J/-40°C

-

Hardox 450 Tuf 1)

-Min. 27 J/-20°C 2)

 

1) Impact testing is performed on thicknesses ≥ 6 mm. For thicknesses between 6 - 11.9 mm, sub-size Charpy V-specimens are used. The specified minimum value is proportional to the cross-sectional area of the test specimen, compared to a full-size specimen (10 x 10 mm). Impact testing according to ISO EN 148 per heat and thickness group. Average of three tests.

2) Single value minimum 70% of specified average.

Tolerances

Tolerances
More details are given in SSAB’s brochure 41-General Product Information Strenx, Hardox®, Armox and Toolox-UK and Hardox® Guarantees or at www.ssab.com.


Thickness
Tolerances according to Hardox Thickness Guarantees. Hardox Guarantees meet the requirements of EN 10 029 Class A for plate. For sheet, the guarantees meet the requirements of 1/2 EN 10 051 and EN 10 131 for cold rolled sheet products.


Length and Width
According to SSAB’s dimension program. For plate, the tolerances are according to SSAB´s mill edge standard or tolerances that conform to EN 10 029 and EN 10 131 for cold rolled sheet. Tolerances conform to EN 10 051 for sheet, tighter tolerances available on request.


Shape
Tolerances according to EN 10 029 for plate, EN 10 051 for sheet and EN 10 131 for cold rolled sheet.
 

Flatness
Tolerances are according to Hardox Flatness Guarantees Class D for plate, which are more restrictive than EN 10 029. For sheet, the tolerances are according to Hardox Flatness Guarantees Class A, that offer narrower tolerances compared to EN 10 051. Cold rolled sheet tolerances are according to Hardox® Flatness Guarantees Class B.


Surface Properties
According to EN 10 163-2, Class A Subclass 1.


Bending
Bendability for plate is according to Hardox Bending Guarantees Class E. For sheet, the bendability is according to Hardox Bending Guarantees Class C for cold rolled sheet and Class B for sheet.

Chemical Composition
Carbon Equivalent CET(CEV)

Chemical Composition (heat analysis)

Grade

C*)
(max %)

Si*)
(max %)

Mn*)
(max %)

P*)
(max %)

S *)
(max %)

Cr*)
(max %)

Ni*)
(max %)

Mo*)
(max %)

B*)
(max %)

CR sheet

0.18

0.25

1.30

0.015

0.004

0.10

0.10

0.04

0.003

Sheet & plate

0.26

0.70

1.60

0.025

0.010

1.40

1.50

0.60

0.005

The steel is grain refined. *) Intentional alloying elements.

Carbon Equivalent CET(CEV)

Thickness

CR sheet
0.7 - 2.10

sheet
2.0 - 8.0

plate
3.2 - 4.9

plate
5.0 - 9.9

plate
10.0 - 19.9

plate
20.0 - 39.9

plate
40.0 - 80.0

plate
80.1 - 130.0

Max CET(CEV)

0.33 (0.44)

0.35 (0.48)

0.37 (0.48)

0.38 (0.49)

0.39 (0.52)

0.41 (0.60)

0.43 (0.74)

0.41 (0.67)

Typ CET(CEV)

0.31 (0.39)

0.26 (0.39)

0.29 (0.39)

0.33 (0.45)

0.36 (0.48)

0.38 (0.56)

0.38 (0.61)

0.39 (0.64)

Delivery Conditions

The delivery condition is Q or QT (Quenched or Quenched and Tempered). Hardox 450 plates are delivered with sheared or thermally cut edges, and thicknesses over 80 mm are delivered with mill edge as standard. Hardox 450 sheets are delivered with an as-rolled surface and mill edge as standard. Hardox 450 cold rolled sheets (0.70 - 2.10 mm (0.028 - 0.083")) are supplied as cold rolled surface.

Delivery requirements can be found in SSAB’s brochure 41-General product information Strenx, Hardox®, Armox and Toolox-UK or at www.ssab.com.

Tech Support

Hardox® Documents to Download

Hardox Downloads

Video

Hardox Steel Grades & Shapes