Hardox 400

Hardox 400
The all-around steel that resists wear and abrasion
Hardox 400 is an abrasion-resistant steel with a nominal hardness of 400 HBW. Hardox 400 is an all-around wear resistant steel. Thanks to its high toughness, good bendability and weldability, this steel can be used in structures with moderate wear.
Tech information
Mechanical Properties
Grade | Thickness | Hardness 1) (HBW) | Typical yield strength (MPa), not guaranteed |
|---|---|---|---|
Hardox® 400 sheet | 2.0 - 8.0 | 370 - 430 | 1100 |
Hardox® 400 plate | 4.0 - 130.0 | 370 - 430 | 1100 |
1) Brinell hardness, HBW, according to EN ISO 6506-1, on a milled surface 0.5 – 3 mm below surface. At least one test specimen per heat and 40 tons.
The nominal thickness of supplied plates will not deviate more than +/- 15 mm from the thickness of the test specimen used for hardness testing.
Hardox® is through-hardened. Minimum core hardness is 90 % of the guaranteed minimum surface hardness.
Impact Properties
Grade | Longitudinal test, typical impact energy, Charpy V 10x10 mm test specimen. |
|---|---|
Hardox® 400 sheet & plate 1) | 45J / -40°C |
1) Impact toughness measured upon agreement. For thicknesses between 6 - 11.9 mm, sub-size Charpy V-specimens are used. Impact testing according to ISO EN 148 per heat and thickness group. Average of three tests.
Tolerances
Tolerances
More details are given in SSAB’s brochure 41-General Product Information Strenx, Hardox®, Armox and Toolox-UK and Hardox® Guarantees or at www.ssab.com.
Thickness
Tolerances according to Hardox Thickness Guarantees. Hardox® Guarantees meet the requirements of EN 10 029 Class A for plate and ½ EN 10 051 for sheet.
Length and Width
According to SSAB’s dimension program. For plate, the tolerances are according to SSAB´s mill edge standard or tolerances that conform to EN 10 029. Tolerances conform to EN 10 051 for sheet, tighter tolerances available on request.
Shape
Tolerances are according to EN 10 029 for plate and EN 10 051 for sheet. Flatness Tolerances are according to Hardox Flatness Guarantees Class D for plate, which are more restrictive than EN 10 029. For sheet, the tolerances are according to Hardox®
Flatness
Guarantees Class A, that offer narrower tolerances compared to EN 10 051.
Surface Properties
According to EN 10 163-2, Class A Subclass 1. Bending Bendability for plate is according to Hardox®
Bending
Guarantees Class D. For sheet, the bendability is according to Hardox Bending Guarantees Class A.
Chemical Composition

Chemical Composition (heat analysis)
Grade | C*) | Si*) | Mn*) | P*) | S *) | Cr*) | Ni*) | Mo*) | B*) |
|---|---|---|---|---|---|---|---|---|---|
Sheet & plate | 0.32 | 0.70 | 1.60 | 0.025 | 0.010 | 2.40 | 1.50 | 0.60 | 0.004 |
The steel is grain refined. *) Intentional alloying elements.
Carbon Equivalent CET(CEV)
Thickness | sheet | plate | plate | plate | plate | plate | plate | plate 80.1 - 130 |
|---|---|---|---|---|---|---|---|---|
Max CET(CEV) | 0.28(0.41) | 0.26(0.41) | 0.31(0.47) | 0.32(0.52) | 0.33(0.60) | 0.40(0.59) | 0.43(0.82) | 0.50(0.82) |
Typ CET(CEV) | 0.26(0.39) | 0.24(0.39) | 0.28(0.44) | 0.29(0.48) | 0.31(0.58) | 0.38(0.57) | 0.41(0.65) | 0.48(0.73) |
Delivery Conditions
The delivery condition is Q or QT (Quenched or Quenched and Tempered). Hardox 400 plates are delivered with sheared or thermally cut edges and thicknesses over 80 mm are delivered with mill edge as standard. Hardox® 400 sheets are delivered with an as-rolled surface and mill edge as standard.
Delivery requirements can be found in SSAB’s brochure 41-General product information Strenx, Hardox®, Armox and Toolox-UK or at www.ssab.com.





