Toolox® Hardening

Toolox® is an excellent steel for the production of high performance dies and machine components. Toolox® is based on an ultra-clean steel metallurgical concept that gives it extraordinary properties. A combination of high strength, crack resistance and optimized workshop properties make it an ideal choice in situations with the highest demands. The guaranteed toughness as well as the plate per plate quality control minimizes the risk for early failures.
For some applications, the surface properties need to be further improved. In such cases, laser hardening has been shown to be a very efficient method, giving a high surface hardness with a relatively large depth. The combination of laser hardening and Toolox® 44 is especially interesting due to the uniquely high yield strength of Toolox® 44. Below the laser hardened layer there will be a very resistant material. Laser hardened surfaces have the further advantage of being very smooth. This reduces friction and the risk for material sticking to the surface.
Another benefit with laser hardening is that it is a very precise and extremely energy efficient method. You only harden the surface that needs hardening and it goes very fast. It only consumes a small amount of electricity, resulting in a very sustainable hardening method.
Laser hardening testing
To increase the knowledge of the laser hardening behavior of Toolox® 44, testing and application development has been made in cooperation with the Swedish laser hardening specialist LaserTool in Blekinge AB (www.lasertool.se). LaserTool in Blekinge AB has since 2003 been pioneering the usage of laser hardening. Since then they have been proven a cutting-edge supplier for many different types of applications, including cold forming dies and advanced machine parts.
LaserTool is using a laser source combined with a robot, zoom optics and a pyrometer for exact temperature control. The surface hardness of Toolox® 44 can be boosted up to 56-60 HRC depending on hardening depth. For Toolox® 33 a surface hardness of 48-52 HRC can be obtained. Hardening depths of 0.2 to 2 mm is possible depending on the application.

Applications
Figure 1. Laser hardening of Toolox® 44 has been used for several types of components. An excellent application is cold forming dies. The die used for stamping thick steel sheet, shown in Figure 1, was previously made in tool steel heat treated to 60 HRc. Cracking after 2000-3000 stampings made that solution unsuitable. Changing to laser hardened Toolox® 44 improved the lifetime to more than 100 000 stampings. The smooth surface also decreases the need for maintenance.

Figure 2. Another successful application is a bushing used in a shot blasting machine, seen in Figure 2. Around the bushing, a shovel wheel is placed. The wear from the wheel and the environment inside the machine represents severe conditions making laser hardening a perfect method to improve lifetime.

Figure 3. For machine components working under the most demanding conditions, laser hardening improves lifetime. SSAB is using laser hardened Toolox® 44 for cutting Hardox® and Strenx® steel plates, as seen in these shearing blades.
Availability
Plates and square blocks from 6–320 mm. Bars between 21 and 405 mm with lengths up to 5000 mm. Toolox® is available from the local SSAB stock. Cut pieces of Toolox® can be obtained through the well-established global network of Approved Toolox® Distributors. Both SSAB and the distributors can provide you with good application support as well as technical guidelines.
Contact and more information
Contact your local sales representative to learn more, visit www.toolox.com or consult Tech Support at: [email protected].

Induction Hardening of Toolox®
Toolox® is an excellent steel for the production of high performance machine components. Toolox® is based on an ultra-clean steel metallurgical concept that gives it extraordinary properties. A combination of high strength, crack resistance and optimized workshop properties make it an ideal choice for all types of machine parts working under the strictest demands. The guaranteed toughness as well as the plate per plate quality control minimizes the risk for early failures.
For some applications, the surface properties need to be further improved. In such cases, induction hardening is a common and very efficient method, giving a high surface hardness with a relatively large thickness. The combination of induction hardening and Toolox® 44 is especially interesting due to the uniquely high yield strength of Toolox®. Below the induction hardened layer there will be a very resistant material.

Induction hardening testing
To increase the knowledge of the induction hardening behavior of Toolox® 44, testing was made at the Swedish induction hardening specialist Teknoheat AB (www.teknoheat.se). Teknoheat is since more than 50 years specialized in designing cutting-edge induction hardening equipment. Therefore they know perfectly well how to optimize the induction hardening result.
Table 1. Induction hardening test parameter
In table 1, the different parameters used for the induction hardening testing can be seen. Water can and should be used always for the cooling. The high crack resistance of Toolox® make the usage of that most efficient cooling method possible.
Sample | % voltage | Heating time | Power | Frequency | Quenching |
|---|---|---|---|---|---|
1 | 72 | 4.1 s | 70 kW | 22 kHz | Water |
2 | 72 | 4.6 s | 70 kW | 22 kHz | Water |
3 | 72 | 5.1 s | 70 kW | 22 kHz | Water |
4 | 77 | 4.6 s | 80 kW | 22 kHz | Water |
5 | 82 | 4.6 s | 90 kW | 22 kHz | Water |
6 | 67 | 5.6 s | 63 kW | 22 kHz | Water |
7 | 67 | 6.6 s | 63 kW | 22 kHz | Water |

Figure 1. The hardness profiles for the different samples
Availability
Plates and square blocks from 6–320 mm. Bars between 21 and 405 mm with lengths up to 5000 mm. Toolox® is available from the local SSAB stock. Cut pieces of Toolox® can be obtained through the well-established global network of Approved Toolox® Distributors. Both SSAB and the distributors can provide you with good application support as well as technical guidelines.
Contact and more information
Contact your local sales representative to learn more, visit www.toolox.com or consult Tech Support at: [email protected].

Flame Hardening of Toolox®
The Toolox® steels are based on an ultra-clean steel metallurgical concept that gives their extraordinary properties. Toolox® 44 is delivered already heat treated to a very high strength as well as a good and guaranteed crack resistance. The excellent fatigue resistance make sure the properties are kept during the whole service time. These characteristics makes Toolox® 44 an ideal choice for all types of machine parts and tools working under the strictest demands.
In most applications Toolox® 44 as delivered is enough. But in some cases the surface properties need to be further improved. In such cases, flame hardening is a common and very efficient method, giving a high surface hardness with a relatively large thickness. The combination of flame hardening and Toolox® 44 is especially interesting due to the uniquely high yield strength of Toolox®. Below the flame hardened layer there will be a very resistant high-quality material.
Picture: Combustol Tratamentos Térmicos. Pieces for the testing supplied by Toolox® distributor Serrametal.
Flame hardening testing
To increase the knowledge of the hardening behavior of Toolox® 44, testing was made at the Brazilian flame hardening specialist Combustol Tratamentos Térmicos (www.combustol.com.br).
Flame hardening is a process that has its limitation in the difficulties to control the parameters exactly. Therefore its extra important to cooperate with professionals like Combustol Tratamentos Térmicos to achieve optimum results. Combustol Tratamentos Térmicos being doing quality heat treatment since 1975 knows perfectly how to get such results.

Test parameters
The test specimen was heated from one side at a temperature of 870 °C during a time of 2.0 minutes. The cooling was done with water directly on the test pieces. Finally, a stress relieving was done at 180 °C during 2 hours.
Picture: Combustol Tratamentos Térmicos.

CP01 – dureza em HV1. As can be seen in the hardness curve, a surface hardness of 650 HV1 was obtained. The case depth defined as 80 % of the surface hardness was estimated to 8.6 mm. Repeating the testing, similar result was obtained showing the consistency of the hardening.
Graphic developed by Combustol Tratamentos Térmicos engineering and R&D department.
Applications
Flame hardened Toolox® 44 is especially suitable for heavy loaded components such as large size gears, wheels and rollers. Also, different part of tooling for metal forming, such as dies and knives.
Availability
Plates and square blocks from 6–320 mm. Bars between 21 and 405 mm with lengths up to 5000 mm. Toolox® is available from the local SSAB stock. Cut pieces of Toolox® can be obtained through the well-established global network of Approved Toolox® Distributors. Both SSAB and the distributors can provide you with good application support as well as technical guidelines.
Contact and more information
Contact your local sales representative to learn more, visit www.toolox.com or consult Tech Support at: [email protected].
