Damatech
High Performance SteelValue Added ProcessingInnovative Industrial SolutionsDamatech

Strenx® Machining

Machined Strenx component

Machining recommendations for Strenx®

Strenx® performance steel can be machined with high speed steel (HSS) or cemented carbide (CC) tools. This brochure includes our suggestions for cutting data (feeds and speeds) and the selection of tools. Other factors that should be taken into account in machining operations are also discussed.

The proposals have been drawn up following our own tests on tools of various makes and in consultation with leading tool manufacturers.

The recommended cutting data and selection of tools also apply to our Strenx® MC, Plus and MC Plus of equal strength grade. For Strenx® 600 MC, Strenx® 650 MC, Strenx® 100, Strenx® 100 XF and Strenx® 110 XF use the same data as for Strenx® 700.

Typical properties for Strenx®



Hardness in Brinell (HBW)

Hardness in Rockwell (HRC)

Tensile strength, Rm (N/mm2)

Strenx® 700

~260

~24

~860

Strenx® 900

~300

~29

~935

Strenx® 960

~320

~32

~990

Strenx® 1100

~430

~43

~1340

Strenx® 1300

~500

~49

~1580

Tool suppliers we recommend and have collaborated with

All the recommendations in this brochure are based on results after practical testing of numerous tools in different situations. We collaborate with some of the world's leading tool manufacturers which we highly recommend using.

Tool suppliers we recommend and have collaborated with


Dorato Tools

www.d-tools.se

Emuge Franken

www.emuge-franken.de

Granlund Tools

www.granlund.com

Hoffmann Group

www.hoffmann-group.com

IZAR Cutting Tools

www.izartool.com

ISCAR

www.iscar.com

Komet Group

www.kometgroup.com

Manigley

www.manigley.ch

Mitsubishi

www.mitsubishicarbide.com

Sandvik Coromant

www.sandvik.coromant.com

SECO TOOLS

www.secotools.com

Witech

www.witec-tools.de

WNT

www.wnt.com

HSS drill for unstable machine conditions

Drilling recommendations

HSS drill

Use only HSS drills when you have unstable machine conditions. HSS drills are only suitable up to 500 Brinell. If the machine conditions are good you have several choices of solid cemented carbide drills, drills with exchangeable heads or indexable insert drills.

Advice for reducing vibrations and increasing the lifetime of the drill

  • Minimize the distance to the column and between the drill tip and the workpiece.
  • Don't use a longer drill than necessary.
  • Always use metal supports and clamp the workpiece securely.
  • Use a solid and stable table.
  • Always use coolant, with a coolant mix of 8-10%.
  • Just before the drill breaks through, disengage the feed rate for about a second — play and springback can otherwise snap the drill tip. Re-engage the feed rate once the play has ceased.
HSS, HSS-E and HSS-Co drills

HSS, HSS-E, HSS-Co

Individual holes can be drilled with an ordinary HSS drill. For rational production, either a microalloyed (HSS-E) drill or a cobalt-alloyed (HSS-Co) drill is recommended. Use an HSS-Co drill (8% Co) with a small helix angle and a robust core that can withstand high torques.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

~ 18

~ 15

~ 7

~ 5

Drill Ø

Feed rate, fn (mm/rev) and speed (rpm)

5

0.06/1150

0.06/950

0.05/445

0.04/280

10

0.12/570

0.11/475

0.10/220

0.08/140

15

0.17/380

0.16/320

0.15/150

0.12/95

20

0.24/290

0.23/240

0.20/110

0.16/70

25

0.30/230

0.29/190

0.25/90

0.20/55

30

0.36/190

0.35/160

0.30/75

0.24/45

Formulas and definitions


Vc = π x d x n/1000

π = 3.14

n = Vc x 1000 / (π x d)

Vc = cutting speed (m/min)

vf = n x fn

n = speed (rpm)


fn = feed rate (mm/rev)


vf = feed rate (mm/min)


d = drill diameter

Drill point geometry showing lip, heel, flute, margin, axis and point angle

Advice for drilling thin plate below 8 mm

  1. It is important to have good support under the plate to avoid deflection.
  2. An indexable drill is recommended, because it begins cutting at the periphery and does not build up the same high pressure as a solid carbide drill.
  3. With a drill diameter over Ø 10 mm and a point angle of 118-140° it is very important to support the plate that is drilled. If the drill tip breaks through the bottom surface without a supporting plate to guide the tip, it may result in an oval and undersized hole.
  4. Reduce feed rate and increase cutting speed Vc, especially when using an indexable drill.
Supporting a thin plate from below while drilling
Indexable insert drill for stable machine conditions

Indexable insert drill

For stable machine conditions and with internal coolant. Important: use as short a drill as possible. The recommendations are for 2ר.

The cutting data for indexable drills has been developed in co-operation with Sandvik Coromant.



Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)


100-150

80-140

50-90

40-70

fn (mm/rev)


min-max

min-max

min-max

min-max

Diameter

12.0-20.0

0.04-0.10

0.04-0.10

0.04-0.10

0.04-0.08


20.01-30.0

0.06-0.12

0.06-0.12

0.06-0.12

0.04-0.10


30.01-44.0

0.06-0.14

0.06-0.14

0.06-0.14

0.06-0.12


44.01-63.5

0.08-0.16

0.08-0.16

0.08-0.16

0.08-0.14

Drills with exchangeable drill heads

For stable machine conditions and with internal coolant.



Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)


70-100

60-90

40-60

35-50

fn (mm/rev)


min-max

min-max

min-max

min-max

Diameter

7.5-12.0

0.08-0.13

0.08-0.13

0.07-0.11

0.06-0.10


12.01-20.0

0.13-0.22

0.13-0.22

0.11-0.15

0.10-0.14


20.01-25.0

0.22-0.28

0.22-0.27

0.15-0.20

0.14-0.18


25.01-33.0

0.28-0.37

0.27-0.36

0.20-0.28

0.18-0.24

Solid cemented carbide drill

For stable machine conditions and with internal coolant.

  • Drilling 7 × Dc: reduce the feed rate by approximately 20%.
  • Drilling with external coolant: reduce the speed and feed rate by approximately 20%.



Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)


70-100

60-90

40-60

35-50

fn (mm/rev)


min-max

min-max

min-max

min-max

Diameter

3.0-5.0

0.03-0.06

0.03-0.06

0.03-0.05

0.03-0.05


5.01-10.0

0.06-0.12

0.06-0.12

0.05-0.11

0.05-0.10


10.01-15.0

0.12-0.18

0.12-0.18

0.11-0.16

0.10-0.15


15.01-20.0

0.18-0.25

0.18-0.24

0.16-0.22

0.15-0.19

WHV and KV9 countersinking and counterboring tools with replaceable inserts

Countersinking and counterboring recommendations

Countersinking and counterboring is best performed using tools with replaceable inserts from the tool supplier Granlund. Always use a rotating pilot and use coolant. See the table below for the tool article number and corresponding screw size. Reduce the cutting data by about 30% for countersinking.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

70-100

40-80

20-50

15-45

fn (mm/rev)

0.10-0.20

0.10-0.20

0.10-0.20

0.10-0.20

Diameter

Speed (rpm)

18.0-26.0

855-1770

490-1415

245-885

185-795

26.0-38.0

590-1225

335-980

170-610

125-550

38.0-47.0

475-840

270-670

135-420

100-380

47.0-60.0

370-680

210-540

105-340

80-305

Countersinking and counterboring table for screws

Size

Article number

Ø screw head

M8

0KV9-18.0

16

M10

0KV9- 20.5 / 1KV9- 20.0

20

M12

0KV9- 25.0 / 1KV9- 26.0

24

M14

1KV9- 30.0

27

M16

1KV9- 30.0 / 2KV9- 32.0

30

M20

2KV9- 38.0

36

M24

2KV9- 40.0

39

Size

Article number

Ø screw head

M10

0WHV- 18.0

16

M12

0WHV- 20.0 / 1WHV- 20.0

18

M14

0WHV- 23.0 / 1WHV- 23.0

21

M16

1WHV- 26.0

24

M20

1WHV- 32.0

30

M24

1WHV- 38.0 / 2WHV- 38.0

36

M30

2WHV-47.0

45

Taps for through holes and blind holes, and chucks for CNC machines

Tapping recommendations

With correct tools and tool holders we recommend tapping up to 500 Brinell with four-flute taps that can withstand the very high torque occurring during tapping in hard materials. If diameter is not critical, the drilled hole can be 3% larger than standard (see the table below). This will increase the lifetime of the tap.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

10-12

7-10

3-5

2.5-3.5

Size

Speed (rpm)

M5

635-765

445-635

-*

-*

M6

530-640

370-530

210-320

-*

M8

400-480

280-400

160-240

100-140

M10

320-380

225-320

125-190

80-110

M12

265-320

185-265

105-160

65-95

M14

225-275

160-225

90-135

57-80

M16

200-240

140-200

80-120

50-70

M20

160-190

110-160

65-95

40-55

M24

130-160

90-135

50-80

30-45

M27

120-140

80-120

45-70

30-40

M30

105-125

75-105

40-65

25-35


* Tapping is not suitable. We recommend thread milling.

Emuge Franken is one tool supplier that has the type of tool holders we recommend for tapping.

Size

Pitch

Drill Ø min-max

M4

0.7

3.3-3.4

M5

0.8

4.2-4.3

M6

1

5.0-5.1

M8

1.25

6.8-6.9

M10

1.5

8.5-8.7

M12

1.75

10.25-10.5

M14

2

12-12.3

M16

2

14-14.3

M20

2.5

17.5-18

M24

3

21-21.5

M27

3

24-24.5

M30

3.5

26.5-27.0

Thread milling recommendations

A CNC machine is necessary for thread milling. The tool supplier can provide programming support for the CNC machines.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

100-130

80-110

50-70

40-60

fz (mm/tooth)

0.03-0.06

0.03-0.06

0.02-0.05

0.02-0.05

Tapping and thread milling advice

  • Taps for blind holes have a shorter tool life due to the smaller core diameter.
  • Before tapping, make sure that the predrilled hole is in good condition (don't use worn out drills).
  • Always use coated taps.
  • Perform thread milling in 2 passes.
  • Make sure that the coolant mix is between 8-10%.
  • We recommend climb milling.
Cutter positioned off-centre to the left to achieve a thicker chip on exit

Milling recommendations

Milling advice

  • Position the cutter off-center (to the left) to achieve a thicker chip at the entry and to avoid a thick chip at the exit.
  • Avoid cutting through the center line of the cutter, as this could generate vibration.
  • Always use down milling (climb milling).
  • The recommendation is that the width of the cut (ae) is 25% or 75-80% of the diameter.
  • Use the rolling-into-cut method.
  • Dry milling is recommended if inserts are used.
  • If machine power is low, use a coarse-pitch cutter.
  • Always use suitable, high-quality clamping equipment.
  • The depth of cut when milling gas-cut edges should be at least 2 mm, to avoid the hard surface layer of the cut edge.

If you enter the workpiece with the rolling-into-cut method the chip thickness on the exit is always zero, and it will help to give a longer tool life.

Formulas and definitions


n= Vc x1000/π x d

π = 3.14

Vc= π x d x n/1000

Vc=cutting speed (m/min)

vf =fz x n x zn

n=speed (rpm)

fz=vf/n x zn

fz= feed rate per tooth (mm/tooth)


vf=feed rate (mm/min)


zn=number of cutting edges


d=tool diameter


ap=cutting depth (mm)

Insert grades for milling by ISO and ANSI class, colour-coded by workpiece material group P, M, K and H, with wear-resistance and toughness arrows

Insert grades for milling

The last two numbers in the insert grade indicate the position of the insert in this scale, whether the insert is optimized for wear resistance or toughness.

Key to the workpiece material groups: ISO P steel, ISO M stainless steel, ISO K cast iron, ISO H hardened steel, and the wear-resistance and toughness arrows
Insert geometry L, M and H compared across edge strength, cutting forces, power consumption, max chip thickness and heat generated

Insert geometry

The macro geometry affects many parameters in the cutting process. An insert with a strong cutting edge can work at higher loads, but it will also generate higher cutting forces, consume more power and generate more heat.

  • Use inserts grade P30-50 with light cutting geometry and a coarse-pitch cutter if the machine power is low and with unstable machine conditions.
Face milling with a 45 degree setting angle, and circular ramping

Face milling recommendation with a 45° setting angle

In very stable machine conditions and with a rigid set-up the insert grade P10 would be more suitable in all milling operations with inserts. The cutting speed can then be increased by approximately 80-100%. The data below is a recommendation for average machine conditions.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

200-250

180-220

110-150

100-140

Feed rate (fz)

min-max

min-max

min-max

min-max


0.15-0.35

0.15-0.35

0.15-0.35

0.15-0.35

Face milling recommendation with round inserts

Round inserts have strong cutting edges and are good to use when the surface has holes and cavities. Recommendation for average machine conditions.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

200-250

180-220

110-150

100-140

Feed rate (fz)

min-max

min-max

min-max

min-max


0.10-0.25

0.10-0.25

0.10-0.25

0.10-0.25

Shoulder milling recommendation with a 90° setting angle

Recommendation for average machine conditions.


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

200-250

180-220

110-150

90-130

Feed rate (fz)

min-max

min-max

min-max

min-max


0.12-0.25

0.12-0.25

0.12-0.25

0.12-0.25

Slot milling with depth of cut limited to half the cutter diameter

Slot milling advice

Depth of cut (ap) max 0.5 × D. End milling recommendation for a solid cemented carbide tool.

  • The fz and pitch per revolution are recommendations for Coromill 210 from Sandvik Coromant.



Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)


95-120

85-110

70-95

45-70

Feed rate (fz)


min-max

min-max

min-max

min-max

Diameter

3.0-6.0

0.01-0.035

0.01-0.03

0.01-0.03

0.01-0.025


8.0-12.0

0.04-0.07

0.04-0.07

0.03-0.06

0.03-0.05


14.0-20.0

0.07-0.10

0.07-0.10

0.06-0.08

0.05-0.07


Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)

200-250

180-220

110-150

100-140

Feed rate (fz)

min-max

min-max

min-max

min-max

Insert grade P30

0.15-0.35

0.15-0.35

0.15-0.35

0.15-0.35

Shoulder milling advice

Use the whole cutting length for ap; radial depth of cut (ae) max 0.1 × D.

  • If possible, use only compressed air to remove the chip, and use a Weldon chuck for tools over Ø 10 mm.



Strenx® 700

Strenx® 900/960

Strenx® 1100

Strenx® 1300

Vc (m/min)


210-240

180-210

160-190

120-150

Feed rate (fz)


min-max

min-max

min-max

min-max

Diameter

3.0-6.0

0.02-0.05

0.02-0.04

0.02-0.04

0.015-0.035


8.0-12.0

0.07-0.10

0.06-0.09

0.06-0.09

0.05-0.07


14.0-20.0

0.10-0.14

0.10-0.13

0.10-0.12

0.08-0.10

Turning showing cutting speed Vc, spindle speed n, feed rate fn and depth of cut ap

Turning recommendations

The cutting data recommendations below are applicable for tough cemented carbide grades. These grades are necessary for operations in which impact may occur, such as when turning plate with gas-cut edges.

  • At higher feed rate, reduce the cutting speed.

Insert grades

P25 / C6

P35 / C6-C7

K20 / C2

Feed rate fn (mm/rev)

0.1 - 0.4 - 0.8

0.1 - 0.4 - 0.8

0.1 - 0.3


Cutting speed Vc (m/min)

Strenx® 700

285-195-145

230-150-100

-

Strenx® 900/960

130-90-70

105-65-45

-

Strenx® 1100

130-90-70

105-65-45

-

Strenx® 1300

-

-

100-80

Formulas and definitions


Vc = π x d x n/1000

π = 3.14

n = Vc x1000/π x d

Vc = cutting speed (m/min)

vf = n x fn

n = speed (rpm)


fn = feed rate (mm/rev)


vf = feed rate (mm/min)


d = workpiece Ø


ap = cutting depth (mm)

Troubleshooting matrix for drilling: ten symptoms cross-referenced against remedies such as a tougher carbide grade, coolant flow and cutting data

Troubleshooting for drilling and milling

The matrices below cross-reference each symptom against the remedies that apply to it — drilling first, then milling.

Troubleshooting matrix for milling: nine symptoms cross-referenced against remedies such as cutter position, feed rate and insert grade

Tool recommendations

The tools below have been tested by SSAB together with the manufacturers. Article numbers and diameter ranges are the manufacturers' own; contact the supplier for current details.

High speed steel drill alloyed with 8% cobalt (HSS-Co 8%) - Alpen-MayKestag, Austria. www.alpenmaykestag.com

High speed steel drill alloyed with 8% cobalt (HSS-Co 8%)

Supplier: Alpen-MayKestag, Austria. www.alpenmaykestag.com

Tool name

Article number

Diameter range

HSS -E Co 8 Taper Shank Drills, WN 103

832xxxxx

8.0-40.0

High speed steel drill alloyed with 8% cobalt (HSS-Co 8%) - Witec, Germany. www.witec-tools.de

High speed steel drill alloyed with 8% cobalt (HSS-Co 8%)

Supplier: Witec, Germany. www.witec-tools.de

Tool name

Article number

Diameter range

TYPE WITEC MN

2-135 15 VAP

10.0-40.0

High speed steel drill alloyed with 8% cobalt (HSS-Co 8%) - Somta, South Africa. www.somta.co.za

High speed steel drill alloyed with 8% cobalt (HSS-Co 8%)

Supplier: Somta, South Africa. www.somta.co.za

Tool name

Article number

Diameter range

MTS Armour Piercing drill

261xxxx

10.0-50.0

High speed steel drill alloyed with cobalt - Izar, Spain. www.izartool.com

High speed steel drill alloyed with cobalt

Supplier: Izar, Spain. www.izartool.com

Tool name

Article number

Diameter range

Ref 1054

32xxx

2.0-12.0

High speed steel drill alloyed with cobalt

High speed steel drill alloyed with cobalt

(DRILL BIT COBALT”S”+ X-ALCR TAPER STUB). Supplier: Izar, Spain. www.izartool.com

Tool name

Article number

Diameter range

Ref 1054

xxxxxx

14.0-30.0

High speed steel drill alloyed with 8% cobalt - Presto tools, England. www.presto-tools.co.uk

High speed steel drill alloyed with 8% cobalt

(HSCo - 8%) Supplier: Presto tools, England. www.presto-tools.co.uk

Tool name

Article number

Diameter range

Armour Piercing drill (APX)

11211 xx.xx

5.0-32.0

Solid cemented carbide drill - Emuge Franken, Germany. www.emuge.de/english

Solid cemented carbide drill

Supplier: Emuge Franken, Germany. www.emuge.de/english

Tool name

Article number

Diameter range

EF-Drill-STEEL

TA203344.xxxx

2.8-16.0

Solid cemented carbide drill - Sandvik Coromant AB, Sweden. www.sandvik.coromant.com

Solid cemented carbide drill

Supplier: Sandvik Coromant AB, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

Cordrill R840 Delta C

R840-xxxx-30-A1A

3.0-20.0

Solid cemented carbide drill - Granlund Tool AB, Sweden. www.granlund.com

Solid cemented carbide drill

Supplier: Granlund Tool AB, Sweden. www.granlund.com

Tool name

Article number

Diameter range

THUNDER / T80

T80-xx.x

10.0-30.0

Solid cemented carbide drill - Mitsubishi, Japan. www.mitsubishicarbide.com

Solid cemented carbide drill

Supplier: Mitsubishi, Japan. www.mitsubishicarbide.com

Tool name

Article number

Diameter range

MPS1 (DP 1021)

MPS1-xxxxS

3.0-20.0

Solid cemented carbide drill - Seco, Sweden. www.secotools.com

Solid cemented carbide drill

For hardness grade 450 Brinell and below, otherwise M-geometry. Supplier: Seco, Sweden. www.secotools.com

Tool name

Article number

Diameter range

Seco Feedmax

* SD203A-12,0-36-12R1

2.0-20.0

Solid cemented carbide drill - WNT, Germany. www.wnt.com

Solid cemented carbide drill

Supplier: WNT, Germany. www.wnt.com

Tool name

Article number

Diameter range

WTX-UNI

11780

3.0-25.0

Solid cemented carbide drill - Hoffmann-Group, Germany. www.hoffmann-group.com

Solid cemented carbide drill

Supplier: Hoffmann-Group, Germany. www.hoffmann-group.com

Tool name

Article number

Diameter range

Garant 122500

122500

1.0-20.0

Drill with exchangeable drill heads

Drill with exchangeable drill heads

Drill head grade: IDI SG IC908. Supplier: Iscar, Israel. www.iscar.com

Tool name

Article number

Diameter range

Chamdrill

DCM xxx-xxx-xxA-3D

7.5-25.9

Drill with exchangeable drill heads

Drill with exchangeable drill heads

Drillheads grade: ICP IC 908. Supplier: Iscar, Israel. www.iscar.com

Tool name

Article number

Diameter range

SumoCham

DCN xxx-xxx-xxA-3D

6.0-32.0

Drill with exchangeable drill heads - Hoffmann-Group, Germany. www.hoffmann-group.com

Drill with exchangeable drill heads

Drillheads grade: P-geometry (HB 7530). Supplier: Hoffmann-Group, Germany. www.hoffmann-group.com

Tool name

Article number

Diameter range

HiPer-Drill

DCN xxx-xxx-xxA-3D

13.0-32,75

Drill with exchangeable drill heads - Sandvik Coromant AB, Sweden. www.sandvik.coromant.com

Drill with exchangeable drill heads

Drillheads grade: P-geometry (PM 4234). Supplier: Sandvik Coromant AB, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

CoroDrill 870

870-xxxx-xxxx

10.0-33.0

Indexable insert drill - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Indexable insert drill

Insert grade: Center insert LM 1044. Peripheral insert LM 4044 Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

CoroDrill 880

880-Dxxxxxxx-xx

12.0-63.0

Indexable insert drill - Seco, Sweden. www.secotools.com

Indexable insert drill

Insert grade: T250D with P1 geometry Supplier: Seco, Sweden. www.secotools.com

Tool name

Article number

Diameter range

Perfomax

SD503-xx.x-xxR7

15.0-59.0

Counterboring in Strenx® - Granlund Tool, Sweden. www.granlund.com

Counterboring in Strenx®

Use a counterbore with indexable inserts, and make sure the insert grade always ends with H. Supplier: Granlund Tool, Sweden. www.granlund.com

Tool name

Article number

Diameter range

WHV counterbore

XWHV-xx.x

18.0-75.0

Countersinking in Strenx® - Granlund Tool, Sweden. www.granlund.com

Countersinking in Strenx®

Use countersink with indexable inserts and the inserts grade should always end with H. Supplier: Granlund Tool, Sweden. www.granlund.com

Tool name

Article number

Diameter range

KV countersink

xKV9-xx.x

20.5-60.0

Tapping in Strenx® - Manigley, Switzerland. www.manigley.ch

Tapping in Strenx®

Tap for through holes. HSSE-PM tap with TiCN coating Supplier: Manigley, Switzerland. www.manigley.ch

Tool name

Article number

Diameter range

105/4 DUO

433xx

M3-M30

Tap for blind holes - Manigley, Switzerland. www.manigley.ch

Tap for blind holes

HSSE-PM tap with TiCN coating Supplier: Manigley, Switzerland. www.manigley.ch

Tool name

Article number

Diameter range

131/3 DUO

433xx

M3-M36

Tap for through holes - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tap for through holes

HSS-E-PM with CoolTop coating Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

CoroTap 200

E324 / E326

M3-M20

Tap for through holes - Hoffmann-Group, Germany. www.hoffmann-group.com

Tap for through holes

HSSE-PM with TiAlN coating Supplier: Hoffmann-Group, Germany. www.hoffmann-group.com

Tool name

Article number

Diameter range

Garant 132065

132065-Mxx

M3-M16

Tap for through holes - BASS, Germany. www.bass-tools.com

Tap for through holes

HSSE-PM with TiCN coating Supplier: BASS, Germany. www.bass-tools.com

Tool name

Article number

Diameter range

VARIANT 1/2 TIH

1088XX

M2-M16

Thread milling in Strenx® - Emuge Franken, Germany. www.emuge.de/english

Thread milling in Strenx®

Solid carbide thread milling cutter with TiCN coating Supplier: Emuge Franken, Germany. www.emuge.de/english

Tool name

Article number

Diameter range

GF-VZ-VHM-R15-IKZ-HB

GFB35106.xxxx

M6-M24

Solid carbide thread milling cutter with TiCN coating - Emuge Franken, Germany. www.emuge.de/english

Solid carbide thread milling cutter with TiCN coating

Supplier: Emuge Franken, Germany. www.emuge.de/english

Tool name

Article number

Diameter range

GSF-VHM 2D IKZ-HB

GF333106.xxxx

M3-M16

End milling in Strenx® - Seco, Sweden. www.secotools.com

End milling in Strenx®

Solid carbide end milling cutter with Siron-A coating Supplier: Seco, Sweden. www.secotools.com

Tool name

Article number

Diameter range

JS 554 Siron-A

JS554xxxx

3.0-25.0

Milling with inserts in Strenx® - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Milling with inserts in Strenx®

Face milling with Coromill 345 Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

Coromill 345

345-xxxxxx-13x

40-250

Face milling with Coromill 300 - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Face milling with Coromill 300

(Round inserts) Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

Coromill 300

R300-xxxxxx-xxx

10-200

Shoulder/face milling with Coromill 490 - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Shoulder/face milling with Coromill 490

Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

Coromill 490

490-xxxxx-xxx

20-250

Shoulder/face milling with Coromill 490 - Sandvik Coromant, Sweden. www.sandvik.coromant.com (detail)
Holemaking with high feed milling - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Holemaking with high feed milling

Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number

Diameter range

Coromill 210

R210-xxxxx-xxx

25-160

Insert grade in Strenx® - Sandvik Coromant, Sweden. www.sandvik.coromant.com

Insert grade in Strenx®

Use insert grade P1030 for average machine conditions. In very stable machines and with a rigid set-up the insert grade P1010 would be more suitable, especially over 500 Brinell. Supplier: Sandvik Coromant, Sweden. www.sandvik.coromant.com

Tool name

Article number/insert grade

Insert geometry

Coromill 210

R210-xxxxxxx-Px 1010

M


R210-xxxxxxx-Px 1030

M

Coromill 300

R300-xxxxx-Px 1010

L-M-H


R300-xxxxx-Px 1030

L-M-H

Coromill 345

345R-1305x-Px 1010

L-M-H


345R-1305x-Px 1030

L-M-H

Coromill 490

490R-xxxxxxx-Px 1010

L-M


490R-xxxxxxx-Px 1030

L-M-H

Portable magnetic drilling machines for Strenx® - Rotabroach, United Kingdom. www.rotabroach.co.uk

Portable magnetic drilling machines for Strenx®

Rotabroach Scorpion Supplier: Rotabroach, United Kingdom. www.rotabroach.co.uk

Model number

Type of drill

Diameter range

Rotabroach Scorpion (Model CM 500)

TCT cutter for Strenx® (core drill)

12-100

Portable magnetic drilling machines for Strenx® - Rotabroach, United Kingdom. www.rotabroach.co.uk (detail)
Portable magnetic drilling machines for Strenx® - Rotabroach, United Kingdom. www.rotabroach.co.uk (detail)
Portable magnetic drilling machines for Strenx® - Rotabroach, United Kingdom. www.rotabroach.co.uk (detail)

The contents of this brochure represent general suggestions. SSAB accepts no responsibility for their suitability in individual cases. The user is therefore responsible to make the necessary adaptations to the conditions in each individual case.

Source: SSAB, 421-EN Machining recommendations for Strenx®, V1 2026.