Damatech
High Performance SteelValue Added ProcessingInnovative Industrial SolutionsDamatech

Strenx® Bending

A Strenx plate being bent in a press brake

Bending of Strenx®

This guide provides guarantees and recommendations for bending Strenx® performance steel which will help you to achieve the best bending results.

Bending high-strength steel is usually straightforward, but you must still consider certain parameters. A highly pure material with few inclusions is fundamental to achieving a good bending result. SSAB's modern processing allows for high standards of surface quality, tolerances and mechanical properties.

Figure 1: bending transverse to the rolling direction, showing punch radius Rp, die entry radius Rd, die width w and plate thickness t

Preparation before bending

  • Check the rolling direction of the plate. If possible, orient the rolling direction perpendicular to the bend line. The plate can often be bent tighter this way than with the bend line parallel to the rolling direction.
  • Check the surface quality of the plate. Surface damage can worsen bendability as it can be the cause of fractures. For heavy plates, defects such as scratches and rust can often be removed with careful grinding. Grinding scratches shall preferably be placed perpendicular to the bend line.
  • Thermal cut and sheared edges should be deburred and rounded with a grinder.
  • Check the condition of your tools.
  • To avoid excessive tool wear, tooling should be harder than the work piece.
  • Check that the tools and tool setup are in line with the recommendations given in this brochure.
Figure 2: the difference between air bending and bottom bending, with the tension and compression sides marked

To consider

  • Always take safety precautions and follow local safety regulations. Only qualified people may be by or in the vicinity of the machine. When high-strength steel is being bent, nobody should stand in front of the press brake.
  • Check that the punch together with the workpiece do not bottom out in the die.
  • Consider springback. Avoid rebending to correct the profile angle. The exposure of a material to previous forming processes reduces its bendability to a great extent.
  • Bending force, springback and, in general, minimum recommended punch radius increase with the strength of the steel.
  • In many Strenx® plate products, the identity of the plate is stamped perpendicular to the rolling direction. Avoid placing the bend line over the stamp due to the risk of cracking.
  • Excessive blast cleaning can have a negative effect on bendability. Recommendations for Strenx® plate products are based on tests with blast cleaned and painted surfaces.
  • High strain rate may cause a local temperature increase in the bend. This could have an adverse impact on the bendability, especially for thicknesses above 20 mm. If possible, reduce the punch speed in order to decrease the temperature difference within the workpiece.
Press brake tooling in a workshop

Tools

Die width

Springback increases with die width, while bending force is reduced. Make sure that the opening angle of the die allows for over-bending, without bottoming out, to compensate for springback. An increased die opening width can in many cases lower the strain level in the bend. Also, make sure that there is enough room for the chosen punch together with the workpiece in the die during bending, without deforming the die. The minimum recommended die opening widths are shown in Tables 2 and 3.

The die edge radius should be at least half the plate thickness. Alternatively, the die width should be increased in order to minimize pressure on the die edge radius, and consequently reduce the risk of die marks.

Figure 3: separation of the plate and punch during bending, so the final inner radius becomes smaller than the punch radius

Punch

The suitable punch radius, along with the die width, is the most important parameter when bending Strenx®. When bending Strenx®, the final inner radius often becomes somewhat smaller than the radius of the punch. When there is low friction between plate and tools, the phenomenon becomes more obvious.

For a steel with a yield strength over approximately 600 MPa, a punch radius that is bigger than the desired remaining inner radius should be used. Tables 2 and 3 show the minimum recommended punch radius when bending to 90°, and the final inner radius that can be achieved.

Punch and die tooling for bending high-strength steel

Condition of tools

Due to the increased contact pressure between plate and tools when bending high-strength steel, wear on the tools increases somewhat. Check regularly that the punch radius and die edge radius are both constant. For bent material that has cracked during manufacturing of a component or part, the crack has in many cases propagated from the compression side of the bend. This can often be attributed to poor punch condition. The edges of the die should remain clean and undamaged.

Machine stability

The forces are often high when bending high-strength steel. The force from the punch acts on the surface of the steel and the friction between the steel and the tools will affect the bending result and the required force.

The static friction coefficient is typically higher than the kinetic. This can cause the plate to lock over one die edge radius, and at the same time slide over the other one. In this way, the workpiece swings down into the die in a discontinuous way during the bending process. This phenomenon, called stick-slip, can result in higher strains over the bend. Use a stable machine and steady tool fastening. Lubrication of the die edge or use of a rotating die edge radius can be helpful, avoiding stick-slip and also lowering the bending force.

Figure 4: crowning - a straight profile, a profile curved along the bend line, and a curved profile angle

Crowning

Crowning compensates for the elastic deflection of the bending machine under load. The central part of punch and die deflects the most. By crowning, the deflection (C) can be compensated for, thus achieving the same bending angle along the entire blank length. If the bend profile becomes curved along the bend line (B), this cannot be compensated for by crowning.

After unloading, compressive stresses arise on the stretched side at the same time as tensile stresses appear on the compressed side. The stress distribution over the plate thickness causes longitudinal stresses. It is those stresses that tend to curve the profile. The magnitude of curvature depends mainly on the flange height and the profile stiffness.

Additional considerations have to be made when setting the crowning at stepwise bending of long profiles.

Formula for estimating bend force P from bend length, plate thickness, tensile strength, die width, die entry radius and punch radius

Bending force

To make an estimation of the force needed during bending, consider not only the bend length, plate thickness, die width and tensile strength, but also the changing moment arm during bending. The peak load is assumed to be reached at a bend opening angle of 120° with normal friction (no lubrication). Trial tests are always recommended.

  • P = Bend force, metric tons
  • t = Plate thickness, mm
  • W = Die width, mm
  • b = Bend length, mm
  • Rm = Tensile strength, MPa (see Table 1)
  • Rd = Die entry radius, mm
  • Rp = Punch radius, mm
SSAB BendCalc app icon

SSAB BendCalc

Consult SSAB's BendCalc app, the first app that predicts springback and punch depth, to get the correct bending settings for Strenx®. Based on the steel characteristics, die and tool symmetry, final bend shape, and friction conditions the BendCalc app gives you the result in seconds:

  • Maximum bend force
  • Springback
  • Punch depth
  • Opening angle during maximal stroke
  • Minimum flange height

You can save the results and share the report as a PDF.

TABLE 1 Typical tensile strength values to calculate bend force.


Grade

Typical tensile strength (MPa)

Strenx® 100

840

Strenx® 100 XF

800

Strenx® 110 XF

850

Strenx® 700 E/F

850

Strenx® P700

850

Strenx® 700 OME

850

Strenx® 900 E/F

1 020

Strenx® 960 E/F

1 060

Strenx® 1100 E/F

1 420

Strenx® 1300 E/F

1 520

Strenx® 600MC D/E

730

Strenx® 650MC D/E

800

Strenx® 700MC D/E

850

Strenx® 700MC Plus

820

Strenx® 700 CR

1 090

Strenx® 900MC

1 070

Strenx® 900 Plus

1 040

Strenx® 960MC

1 110

Strenx® 960 Plus

1 090

Strenx® 960 CR

1 200

Strenx® 1100MC

1 320

Strenx® 1100 CR

1 400

Strenx® 700 HR W

870

Strenx® 700 CR W

1 090

Strenx® 960 HR W

1 150

SSAB Tech Support specialists

Springback

Springback increases with steel strength and the ratio between die width and plate thickness (W/t). Material yield strength has the biggest influence.

When bending, a varying residual stress distribution is achieved over the bend cross section. The plastic strain level and the distribution of these stresses will control the tendency for springback. All springback is fully elastic. To compensate for springback, the die should be shaped in such a way to allow overbending without coining the material.

It is very difficult to accurately predict the springback of a material when bending, since this depends to a large extent on each unique tool setup. That is why trials are recommended. For thinner plate or sheet (t < 10 mm), you can estimate the material's springback by dividing the tensile strength (MPa) by 100. A precondition is that the die width is approximately 10–12 × the plate thickness.

Parameters that affect springback

  • Yield strength of the material — higher yield strength causes greater springback.
  • Punch radius — increased punch radius will cause greater springback.
  • Die width — larger die width causes greater springback.
  • The strain hardening of the material.

Bending guarantees and recommendations

Since SSAB's products are developed and specialized for different types of use, bend tests and evaluation of these vary somewhat.

For plate products the minimum recommended relationship between the punch radius and plate/sheet thickness (R/t) is shown in Tables 2 and 3, along with corresponding recommendations for sheets. These bend recommendations are based on bend tests of one step to 90° after unloading. Die opening widths are guidelines and may vary somewhat.

Strenx® is delivered with guaranteed bending performance according to the Strenx® guarantee. For more information contact your local SSAB representative, or SSAB Tech Support.

TABLE 2 STRENX® PLATE, bending guarantees and recommendations.


The bending guarantees and recommendations for Strenx® plate are based on dies with rolls and normal friction (no lubrication). R/t stands for radius (R) divided by sheet thickness (t). Ri/t is the guaranteed minimum final inner radius; Rp/t is the recommended minimum punch radius.


Grade/Product

Nominal thickness (t) (mm)

Ri/t transverse to rolling direction

Ri/t along rolling direction

Rp/t transverse to rolling direction

Rp/t along rolling direction

Die opening width (W) minimum W/t

Strenx® 700E/F / Strenx® 100 / Strenx® P700 / Strenx® 700 OME

t < 8

1.3

1.8

1.5

2.0

10


8 ≤ t < 15

1.3

1.8

1.5

2.0

10


15 ≤ t < 20

1.7

2.1

2.0

2.5

12


t ≥ 20

1.7

2.1

2.0

2.5

12

Strenx® 900E/F / Strenx® 960E/F

t < 8

2.3

2.5

2.5

3.0

12


8 ≤ t < 15

2.3

2.6

2.5

3.0

14


15 ≤ t < 20

2.4

2.7

2.5

3.0

14


t ≥ 20

2.8

3.4

3.0

3.5

16

Strenx® 1100E/F

t < 8

2.8

3.3

3.0

3.5

12


8 ≤ t < 15

2.6

3.2

3.0

3.5

14


15 ≤ t < 20

2.5

3.1

3.0

3.5

14


t ≥ 20

3.0

3.5

3.5

4.0

16

Strenx® 1300E/F

t < 8

3.1

3.8

3.5

4.0

14


8 ≤ t ≤ 15

3.6

4.3

4.0

4.5

14

TABLE 3 STRENX® SHEET, bending guarantees and recommendations.


The bending guarantees and recommendations for Strenx® sheet are based on dies with rolls and normal friction (no lubrication). R/t stands for radius (R) divided by sheet thickness (t). Ri/t is the guaranteed minimum final inner radius; Rp/t is the recommended minimum punch radius.


Grade/Product

Nominal thickness (t) (mm)

Ri/t transverse to rolling direction

Ri/t along rolling direction

Rp/t transverse to rolling direction

Rp/t along rolling direction

Die opening width (W) minimum W/t

Strenx® 600MC D/E

t ≤ 3

0.7

0.7

0.7

0.7

10


3 < t ≤ 6

1.1

1.1

1.1

1.1

10


t > 6

1.4

1.4

1.4

1.4

10

Strenx® 650MC D/E / Strenx® 100 XF

t ≤ 3

0.8

0.8

0.8

0.8

10


3 < t ≤ 6

1.2

1.2

1.2

1.2

10


t > 6

1.5

1.5

1.5

1.5

10

Strenx® 700MC D/E / Strenx® 110 XF

t ≤ 3

0.8

0.8

1.0

1.0

10


3 < t ≤ 6

1.2

1.2

1.4

1.4

10


t > 6

1.6

1.6

1.7

1.7

10

Strenx® 700 HR W

3 ≤ t ≤ 6

1.2

1.2

1.4

1.4

10


t > 6

1.6

1.6

1.7

1.7

10

Strenx® 700MC / Plus

3 ≤ t ≤ 10

1.0

1.0

1.3

1.3

10


t > 10

1.5

1.5

1.8

1.8

10

Strenx® 900MC

3 ≤ t ≤ 8

3.0

3.0

3.7

4.0

12


t > 8

3.5

3.5

4.0

4.5

12

Strenx® 900 Plus

2 ≤ t ≤ 8

3.0

3.0

4.0

4.0

12

Strenx® 960MC

3 ≤ t ≤ 10

3.5

3.5

3.6

4.0

12

Strenx® 960 Plus

2 ≤ t ≤ 8

3.5

3.5

4.0

4.2

12

Strenx® 960 HR W

3 ≤ t ≤ 6.1

3.5

3.5

4.0

4.0

12

Strenx® 1100MC

3 ≤ t ≤ 8

4.0

4.0

4.7

5.0

14

Strenx® 700 CR

0.7 ≤ t ≤ 2.1

2.0

2.0

2.5

2.5

10

Strenx® 960 CR

0.8 ≤ t ≤ 2.1

3.5

3.5

4.5

4.5

12

Strenx® 1100 CR

0.8 ≤ t ≤ 2.1

3.5

3.5

4.5

4.5

14

Source: SSAB, 422-EN Bending of Strenx®, V1 2026. For information about other materials and more technical information, contact SSAB Tech Support.