Duroxite® Forming
Duroxite® FORMING
Duroxite ® is typically formed with the overlay to the inside, but can be formed with the overlay to the outside. The staggered cracking pattern on the overlay surface ensures good formability.
Duroxite ® plates CANNOT be formed parallel to the welding bead direction. It's highly recommended to form Duroxite ® plates with a roll bending machine. Forming by a press brake is not recommended due to local stress concentration spots generated which could cause spalling or cracking during bending.
Duroxite ® PIPE is recommended for pipes with diameters under 0.6 m (24') instead of pipes fabricating from plate. See charts for minimum forming radius recommendations.
DUROXITE ® 100 AND DUROXITE ® 200
Thickness | Min. inside radius* with overlay side in | Min. outside radius* with overlay side out |
|---|---|---|
3 mm on 6 mm 1/8' on 1/4' | 300 mm 12' | 900 mm 36' |
5 mm on 8 mm 3/16' on 5/16' | 300 mm 12' | 1100 mm 44' |
6 mm on 6 mm 1/4' on 1/4' | 300 mm 12' | 1200 mm 48' |
6 mm on 10 mm 1/4' on 3/8' | 350 mm 14' | 1400 mm 56' |
10 mm on 10 mm 3/8' on 3/8' | 400 mm 16' | 1500 mm 60' |
12 mm on 12 mm 1/2' on 1/2' | 700 mm 28' | 1800 mm 72' |
DUROXITE ® 300 AND DUROXITE ® 500
Thickness | Min. inside radius* with overlay side in | Min. outside radius* with overlay side out |
|---|---|---|
3 mm on 6 mm 1/8' on 1/4' | 400 mm 15' | 1550 mm 60' |
5 mm on 8 mm 3/16' on 5/16' | 500 mm 18' | 1850 mm 72' |
6 mm on 6 mm 1/4' on 1/4' | 500 mm 18' | 1850 mm 72' |
6 mm on 10 mm 1/4' on 3/8' | 550 mm 21' | 2050 mm 80' |
10 mm on 10 mm 3/8' on 3/8' | 650mm 25'' | 2600 mm 100'' |
DUROXITE ® 101 AND DUROXITE ® 201
Thickness | Min. inside radius* with overlay side in | Min. outside radius* with overlay side out |
|---|---|---|
3 mm on 6 mm 1/8' on 1/4' | 300 mm 12' | 950 mm 36' |
5 mm on 8 mm 3/16' on 5/16' | 300 mm 12' | 1200 mm 44' |
6 mm on 6 mm 1/4' on 1/4' | 300 mm 12' | 1250 mm 48' |
6 mm on 10 mm 1/4' on 3/8' | 400 mm 15' | 1450 mm 56' |
10 mm on 10 mm 3/8' on 3/8' | 450 mm 17' | 1550 mm 60' |
12 mm on 12 mm 1/2' on 1/2' | 1100 mm 42' | 1850 mm 72' |
Bending in
Bending with hard side facing in closes up the cracks

Bending out
Bending with hard side facing out opens up the cracks

Bending parallel
Duroxite® plates cannot be formed parallel to the welding bead direction.

